The Shimano Crank Tool (SCT for short) is specifically built to service the chainring lockring on Shimano single ring cranksets for 12 speed drivetrains. It features a large hex that can be used with a 1.5" or 38mm wrench or locked into a vise. The clearance hole is kept to a minimum to keep the tool engaged on the low profile lockring, minimizing the chance of damaging the tool or parts. Compatibility: - Chain ring lockrings on Shimano 12spd mountain crank sets. - XT and Ultegra bottom brackets

The lever setter is a unique tool that works in conjunction with our HAG (or other hanger allignment tool) to set brake and shifter levers at the same height from side to side. The tool temporarily replaces the headset top cap and allows you to thread a hanger alignment tool into the lever setter. Use the HAG indicator to set levers the same from one side of the bar to the other. Once you're satisfied with your lever placement simply remove the tool and replace your headset top cap and go ride. Compatibility: Requires a star nut or compression plug with a M6x1 thread. Works with road and mountain shifters and brake levers. Compatible with most hanger alignment tools on the market. Recommendations: It's advised to use a spacer on top of the stem to help align the lever setter with the steer tube. This will reduce the impact the quality of the cut on the steer tube has on the function of the tool. The supplied threaded stud can be replaced with a longer one if needed.

All the awesomeness of the dual-sided tool but in a single Shimano or Campagnolo version. Updated in 2020, the single-sided tool now has the same size handle (1/2 inch) as the dual-sided tool. - When purchasing the chain whip, buy the 1/2-inch handle chain whip.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

This bottom bracket socket is for use on BSA30 16-notch bottom brackets. Made with the same top shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with Chris King's T47 Bottom Bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This bottom bracket socket is for use with Colnago's 30mm Bottom Bracket Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This bottom bracket socket is for use with E Thirteen's BB30 bottom brackets. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with the Praxis M30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

This bottom bracket socket is for use with the TorqTite BSA30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket. This socket features a threaded boss to allow you to bolt the tool into place when dealing with these exceptionally thin tool interfaces. This is a feature unique to our tools that adds a layer of protection and security to your parts and tools.

This tool is compatible with all outboard bearing cups that our dual-sided Shimano socket doesn't fit, including Campagnolo, SRAM, FSA, and older Shimano. These gems start as a 7075 aluminum billet and get precisely machined. We take the time to put some nice deep finger splines in this tool so you can thread the cup into the frame by hand with those greasy fingers you haven't washed in a while. - Hard anodized and laser-engraved with torque specs. - Use your favorite 3/8" square drive ratchet or torque wrench to tighten it down.

The Whip-It maximizes function and simplicity. Made from a 12-inch length of stainless steel, it gives you enough leverage to loosen even the most stubborn cassettes. The Whip-It's round handle provides comfort surpassing other flatbar-style chain whips on the market. The icing on the cake is that Abbey's signature tool, the Crombie, stores inside the handle of the Whip-It; this means the two tools you use together get stored together and travel together, creating less clutter in your tool box.

While most other manufacturers cast or forge their bottom bracket tools, we machine ours for greater precision. Whenever you're dealing with anodized surfaces, great care needs to be taken to keep those surfaces from getting marred, gouged, and stripped out. That can be nearly impossible with some spanner style tools, and difficult with other loose-fitting sockets. The most unique feature about this tool is the inner nub; that nub in the center of the tool is the same size as the crank spindle. What this does is give you a second point of contact that keeps the tool from coming off of the part when trying to remove stubborn cups. This dual sided socket is designed to work with the new Shimano DA-9000/XTR-BB93 bottom bracket as well 6800 Ultegra and 5800 105 11spd groups (BBR-60).

We listened to your requests and created a socket style Crombie tool that is compatible with ratchets and torque wrenches. The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. Compatible with all Campagnolo cassettes.

The Socket Crombie has our signature finger spline at the top along with a 3/8" square drive for using your favorite ratchet or torque wrench. The tool is plenty deep to hide a quick release and still get full engagement on the lock ring. The S Group Socket Crombie is ideal for some of the newer RockShox suspension forks that are using the S group lockring spline for suspension top caps. It is also compatible with all modern Shimano and Sram cassettes.

The Crombie tool is a game changer when it comes to swapping cassettes. Whether you're a professional mechanic swapping cassettes several times a day or a DIY kind of guy, this gem has a place on your tool bench. The first time a quick release spring rolls under your bench the Crombie tool paid for itself. If you like to remove the cassette for a detailed cleaning or just swapping from one cassette to another, it's a big time saver and a breeze to use. This version of the tool has a Shimano/SRAM remover on one side with a Campagnolo on the other. A precision machined spline ensures maximum engagement and durability. The STANDARD version comes with a solid handle which gives the tool some mass making it the preferred choice in the shop. The SUPER LIGHT version shaves 125 grams out of the handle. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. If you commonly come across over torque lockrings get the standard handle!

The Geiszler is a stepped adapter designed to work with every thru-axle fitment currently on the market: 12x142, 12x150, 15x100, 20x110, Lefty and 24 Maverick. The tool will allow precision dishing without removal, a notable time saver when wheel building. The Geiszler can be bolted into the hub with the included stud for serious wheel work. It can also be slipped into place for minor adjustments and retained by the compression of the truing stand. This simple tool eliminates clutter around your truing stand and keeps you from searching for the right adapter. - Made in Bend, Oregon - Bolts and washers for use with single-armed wheel stands are available upon request, for free

With thru axles becoming more and more common, the original Crombie tool was due for a makeover. We took the piloting pin and plus-sized it to work with the 12mm thru axle fitment that is actually standardized. We make this version as a dual-sided tool with two S Group ends, one for thru axle wheels and the other for regular hubs. The regular side has a hole deep enough to hide a skewer nut; it's really the best of both worlds. - Comes with a solid handle - Note: this version of the Crombie tool is not compatible with any Campagnolo wheels. - Dimensions: 9.625in x 1.0in

- A precision multi-tool is a great addition to the shop at home or work - More robust tool than the compact 4 way - Constructed from stainless steel both frame and WERA bits - Available in 2 preconfigured options - Also available as a set which includes: tool frame, 2, 2.5, 3, 4, 5, 6 hex bits, T10, T15, T20, T25, T30 Torx bits, #2 jis Phillips and 1mm slotted screwdriver bits - Made in the USA; Bend, Oregon

- A precision multi-tool is a great addition to the shop at home or work - More robust tool than the compact 4 way - Constructed from stainless steel both frame and WERA bits - Available in 2 preconfigured options - Also available as a set which includes: tool frame, 2, 2.5, 3, 4, 5, 6 hex bits, T10, T15, T20, T25, T30 Torx bits, #2 jis Phillips and 1mm slotted screwdriver bits - Made in the USA; Bend, Oregon

The Crombie tool is a game changer when it comes to swapping cassettes. Whether you're a professional mechanic swapping cassettes several times a day or a DIY kind of guy, this gem has a place on your tool bench. The first time a quick release spring rolls under your bench the Crombie tool paid for itself. If you like to remove the cassette for a detailed cleaning or just swapping from one cassette to another, it's a big time saver and a breeze to use. This version of the tool has a Shimano/SRAM remover on one side with a Campagnolo on the other. A precision machined spline ensures maximum engagement and durability. The STANDARD version comes with a solid handle which gives the tool some mass making it the preferred choice in the shop. The SUPER LIGHT (SL) version shaves 125 grams out of the handle. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. If you commonly come across over torque lockrings get the standard handle!

With thru axles becoming more and more common, the original Crombie tool was due for a makeover. We took the piloting pin and plus-sized it to work with the 12mm thru axle fitment that is actually standardized. We make this version as a dual-sided tool with two S Group ends, one for thru axle wheels and the other for regular hubs. The regular side has a hole deep enough to hide a skewer nut; it's really the best of both worlds. This SUPER LIGHT version has a hollow handle to save weight for the traveling mechanic. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. - Note, this version of the Crombie tool is not compatible with any Campagnolo wheels. - Dimensions: 9.625in x 1.0in

The Charger 2 wrench is designed for use on the lower seal head of Charger 2 and Charger LT dampers. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your suspension fork when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

The Reverb is an advanced and complicated component and service becomes a breeze with this speciality wrench. Designed for use on the inner seal head and upper collet of both 30.9 and 31.6 millimeter version of the Reverb dropper post. This series of wrenches comes as a result of our collaboration with RockShox to develop a series of tools specifically for their suspension components. Built to hold the thin aluminum parts of the dampers to avoid damage. These wrenches are built with the same tool grade aluminum to tight tolerances to give you years of trouble free use. They will not damage or mar the sensitive parts inside your seastpost when used with care, keeping you and your customers happy. They also feature a 3/8" square drive in the middle to use with your favorite torque wrench during reassembly.

- The 4-way precision multi-tool is the perfect choice to carry with you while on a ride. Designed to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket - Stainless steel bits in a beautiful green anodized frame - Available in 5 preconfigured options - Also available as a set which includes: tool frame, 2, 2.5, 3, 4, 5, 6 hex bits, T10, T15, T20, T25, T30 Torx bits, #2 jis Phillips and 1mm slotted screwdriver bits - Made in the USA; Bend, Oregon

The Shop Hammer has a heat-treated 1.5-inch (38mm) stainless steel head and 12-inch long handle with the same silicone grip from ESI as our Team Issue Hammer. Weighing in at a respectably stout 20oz (566g), they are sure to make short work of setting crown races and removing press fit bottom brackets. - Hammer comes standard with green soft face. Brass tips are also available. - Made in Bend, Oregon